EqualLogic PS 初期設定
１、シリアルケーブルでイコールロジックのアクティブコントローラに接続します。
２、グループアカウントでログインします(grpadmin/grpadminがデフォルトです。)
login: grpadmin
Password:
Welcome to Group Manager
Copyright 2001-2013 Dell Inc.
7457173:5:netmgtd:12-Dec-2013 02:25:01.330006:rcc_util.c:1029:INFO::25.2.9:CLI:
Login to account grpadmin succeeded, using local authentication. User privilege
is group-admin.
It appears that the storage array has not been configured.
Would you like to configure the array now ? (y/n) [n]
Please run setup before executing management commands
It appears that the storage array has not been configured. Please run setup befo
re executing management commands.
CLI> setup
Group Manager Setup Utility
It appears that setup was run previously, but it did not
complete. Restarting setup.
Enter the network configuration for the array.
Member name []: demo01
Network interface [eth0]:
IP address for network interface []: 192.168.1.32
Netmask [255.255.255.0]:
Default gateway [192.168.1.1]:
Initializing interface eth0. This may take a minute.....
Enter the IP address and name of the group that the array will join.
Group name []: demogroup
Group IP address []: 192.168.1.31
Searching to see if the group exists. This may take a few minutes.
The group does not exist or currently cannot be reached. Make sure
you have entered the correct group IP address and group name.
Do you want to create a new group (yes | no) [yes]:
Group Configuration
Group Name: demogroup
Group IP address: 192.168.1.31
Do you want to use the group settings shown above (yes | no) [yes]:
Password for managing group membership:
Retype password for verification:
Password for the default group administration(grpadmin) account:
Retype password for verification:
Saving the configuration...
Waiting for configuration to become active....Done
7458263:25:psgd:12-Dec-2013 02:42:30.710026:psgd_group.cc:17372:INFO::18.2.0:Gro
up member demo01 now active in the group.
Group demogroup has been created with one member.
Use the Group Manager GUI or CLI to set the RAID policy
for the member. You can then create a volume which
a host can connect to using an iSCSI initiator.
To access the Group Manager GUI, specify http://group_ip_address in
a Web browser window. To access the CLI, use telnet or SSH to
connect to the group IP address from a remote terminal, or attach a
console terminal directly to a serial port on a group member's
active control module. Log in to the default group administration
account (grpadmin) using the password you specified when creating
this group. See the Group Administration manual for more
information.
demogroup>
5、既存のグループに追加する場合は、下記のようになります。
Enter the IP address and name of the group that the array will join. Group name []: DEMOGROUP Group IP address [192.168.1.31]: Password for managing group membership: Do you want to add this array to group DEMOGROUP (yes | no ) [yes]: Synchronizing configuration data with the group. This may take several minutes.-- Saving the configuration... Waiting for configuration to become active...Done The array has successfully become a member of group DEMOGROUP. You must now configure the RAID set using the Group manager GUI or CLI. Configuration of the RAID set requires that the raid-level be selected. 2820:40:psgd:12-Dec-2013 04:26:52.470041:psgd_group.cc:17372:INFO::18.2.0:Group member DEMO02 now active in the group. 2848:46:psgd:12-Dec-2013 04:26:52.640047:psgd_group.cc:17372:INFO::18.2.0:Group member DEMO01 now active in the group.
